#INSTALL COOLTERM MAC OS X#
#INSTALL COOLTERM INSTALL#
#INSTALL COOLTERM SERIAL#
#INSTALL COOLTERM DRIVER#
#INSTALL COOLTERM FULL#

In contrast to GPIOs, Analog inputs can read voltages at any level between 0 to 3.3V volts. A 470 Ohms series resistor is recommended for current limiting when connecting LED to a GPIO. So no additional circuitry is needed to drive regular LEDs. Please refer to the Technical Specifications at the end of this document for more details). In output mode, GPIOs can source up to 25mA (IO source/sink capacity varies depending on IO. It is recommended to use a series resistor with the GPIO/ADC pins when interfacing with other circuits. The ADC can acquire analog signal at the resolution of 10 bits per sample. All IO pins support 3.3V TTL signals and the ADC input range is 0 to +3.3V.

Some of these pins can be used as Analog to Digital Converter inputs as well. The module has 32 General Purpose IO pins that can be used for various custom applications. Also we have a large set of sample code to help you with)Īll aspects of the above steps are covered in the following sections including step by step demonstration.

Optionally write a script or application to automate your task (More info on custom programming/scripting is available in this document.

Enter commands (Very similar to entering commands at DOS prompt or Bash prompt).

#INSTALL COOLTERM SERIAL#

Open the COM port corresponding to the device using a Serial Terminal software.

#INSTALL COOLTERM DRIVER#

Driver available for download on the product page.)

#INSTALL COOLTERM INSTALL#

Install driver (Only needed for Windows.

Connect the device to a USB port on the host system.

Using this product involves the following simple steps. But in no way limited to this software though. This document has more information about using this device with the following Serial terminal software. Using this product is very easy, thanks to the human readable and easy to use command set and the USB CDC interface that allows the device to be used with most readily available serial terminal software such as Tera Term or HyperTerminal. When connected to PC, the module will appear as a serial port in Windows Device Manager (or a serial tty device in Linux and Mac). The analog inputs (multiplexed with GPIOs) can be accessed over USB interface for extended functionality. This module has 32 on board General purpose I/Os multiplexed with 7 Analog Inputs, each connected to individual screw terminals.

Visual Basic for Applications (Microsoft Office VBA)Ī complete list of sample code is available here.

Visual Basic (VB6, VB2008, VB2010 express and other editions).

Or any other operating system that supports USB CDC devices.Īnd these are some of the languages that can be used for programming:.

Windows XP and later versions (Windows 7, 8/8.1, 10 and future versions).

This product is compatible with the following operating systems: Some of the possible uses of this module includes:

Can be controlled by using standard serial console applications or custom applications.

Can be powered from USB or external power supply.

All IOs available on easy to access screw terminals.

As easy as using a serial port, no USB knowledge required

7 analog inputs with 10-bit resolution (multiplexed with digital IOs).

For power users, this module can be controlled by writing programs in various programming languages. This simplicity allows use of off-the-shelf Terminal Emulation programs such as Hyper Terminal and PUTTY for controlling the module with a simple set of human readable commands. Built in USB to serial conversion allows the module to be used without any USB specific knowledge. Ease of use and wider operating system compatibility are the primary goals behind this product’s design.

#INSTALL COOLTERM FULL#

Other features include full ANSI/VT100 terminal emulation, break-sequence support (for Cisco, etc), a line-buffered send mode, a fully featured SSH/Telent client, and much more.Numato Lab’s 32 Channel USB GPIO Module is a versatile product for controlling electrical and electronic devices remotely from a PC over USB link. If you can't find an OS X driver for yourĪdapter (eg, Belkin), give Serial a try as it'll probably work! The free demo is fully functional for 7 days. Serial Serial is a great Terminal Emulation Program with built-in driver support for most USB to serial devices. Or, ctrl-click/right-click on the app and select Open from the pop-up menu so not to permanently lower your security settings.

If you have trouble installing any of the following (or any other program) with an unidentified developer error, goto: System Preferences ➤ Secrity & Privacy ➤ General and click on Allow Applications Downloaded from: Anywhere and try again. If you can't find a driver for your adapter (eg, Belkin), try Serial which has built-in support for most (if not all) USB-Serial adapters. If you're looking for a command line app, there's Screen (built-in) or Minicom.

#INSTALL COOLTERM MAC OS X#

The following Mac OS X GUI applications are available: Having installed the right driver for our USB-serial adapter, we also need to install some terminal emulation software before we can connect to anything.

Install coolterm